Advances in Earth Science ›› 2004, Vol. 19 ›› Issue (3): 443-450. doi: 10.11867/j.issn.1001-8166.2004.03.0443

• Articles • Previous Articles     Next Articles

MECHANISM OF LARGE SCALE LANDSLIDES IN WESTERN CHINA

HUANG Run-qiu   

  1. National Professional Laboratory of Geological Hazards Prevention, Chengdu University of Technology, Chengdu 610059, China
  • Received:2004-04-09 Revised:2004-04-20 Online:2004-12-20 Published:2004-06-01

HUANG Run-qiu. MECHANISM OF LARGE SCALE LANDSLIDES IN WESTERN CHINA[J]. Advances in Earth Science, 2004, 19(3): 443-450.

China is a big country with various topography types and geological structures, especiallyin its southwestern part, the interior and epigeneticgeological process are very active because of the special location of the margin area of Tibet Plateau. The intensive uplift of the Plateau since the Quarterly time resulted in a distinctive topographical contrast with the plateau and lower basins, high mountains and deep valleys. Moreover, the extension of the Plateau towards the east and southeast resulted from the collision between Indian plate and EuropeAsian one brings about the appearanceof large active faults around the Plateau and strong earthquakes. All of these lay a strong geoenvironmental backgrounds for the occurrence of large scale landslides in this area. 
A lot of evidences show that a new increase period of landslides has comes in China since 1990s,especially some typical hazardous landslides occurred in this period. Even though this kind of increase has been thought to be related to the large scale infrastructures construction, it is a common sense that the fundamental geologicmechanics model should be involved in the sliding process. Therefore, it is very significant to discuss the mechanism of these landslides and summery some typical models. The author's work reveals following typical huge landslides mechanism.
(1) Creeptensionshearing fracture model (three segments mechanism): This kind of mechanism occurs in the slope contained nearly horizontal or gently outinclined soft layers or weak planes. The slope deformation and failure is controlledby the weak plane generally located at the base of the slope. With the unloading process of the slope from river down erosion or slope cutting, the creep deformation occurs along the weak plane and a tension crack will appear at the top of the slope. The continuous creep deformation will promote the gradually deepening of the tension crack and a locked segment will appear at the middle part of the potential slip surface. Obviously, stress will be concentrated at the locked section and this section will be formed to be a key part controlling the slope stability. When the concentrated stress reaches to a criticalextent, the locked section will be cut through with a sudden brittle shearing failure, and a hazardous landslide occurs.
(2) “Retailing wall” collapsemodel: it is generally involved in the slope with a soft base and a rigid section above it. The later one can be regarded as a "locked section" on theslip surface and it acted as a “retailingwall”because it supports the driving force from the upper slope. Obviously, the stress will be accumulated gradually in the “retailing wall”with the increasingof the driving force from the upper slope and the continuous squeezing out deformation of its soft base. Finally, the “retailing wall” located at the middle part of the slope will be destroyed due to exceed stress accumulation, and the slip surface will be formed.
(3) “Super punching”mechanism model: it describes the process that a unstable block slides down from a sharply steep slope or mountain and it impacts very strongly on a debris at the slope foot, and induces the debris integrating suddenly and flowing a long distance in a moment time. Generally, the unstable block has very huge potential energy for its high position and its instabilitycomes very suddenly. The induced debris flow moves very quickly and has almost all the characters of high speed mass flows such as high velocity, long travelingdistance, lower apparent friction angle, special moving trajectory, aircushion effect traces, even forming a lake as it reaches a river. In most cases this kind of model means a big hazard and beyond recall losses. 

No related articles found!
Viewed
Full text


Abstract